Treatment of tomato paste wastewater by electrochemical and membrane processes: process optimization and cost calculation.

This study investigated the treatment of wastewater from tomato paste (TP) production using electrocoagulation (EC) and electrooxidation (EO). The effectiveness of water recovery from the pretreated water was then investigated using the membrane process. For this purpose, the effects of independent control variables, including electrode type (aluminum, iron, graphite, and stainless steel), current density (25-75 A/m2), and electrolysis time (15-120 min) on chemical oxygen demand (COD) and color removal were investigated. The results showed that 81.0% of COD and 100% of the color removal were achieved by EC at a current density of 75 A/m2, a pH of 6.84 and a reaction time of 120 min aluminum electrodes. In comparison, EO with graphite electrodes achieved 55.6% of COD and 100% of the color removal under similar conditions. The operating cost was calculated to be in the range of $0.56-30.62/m3. Overall, the results indicate that EO with graphite electrodes is a promising pretreatment process for the removal of various organics. In the membrane process, NP030, NP010, and NF90 membranes were used at a volume of 250 mL and 5 bar. A significant COD removal rate of 94% was achieved with the membrane. The combination of EC and the membrane process demonstrated the feasibility of water recovery from TP wastewater.

An energy efficiency assessment of Yttrium-aluminum-garnet laser in vitro.

To study the effect range of the Nd:YAG laser through various levels of cloudy medium for targets with varying grayscale values in vitro. The coated paper cards with grayscale values of 0, 50, 100, and 150 were used as the laser's targets, which were struck straightly with varying energies using three burst modes (single pulse, double pulse, and triple pulse). Six filters (transmittances of 40, 50, 60, 70, 80, and 90) were applied to simulate various levels of cloudy refractive medium. Image J software was used to measure the diameters and regions of the laser spots. The ranges of the Nd:YAG laser spots increased with energy in the same burst mode (P < 0.05). Under the same amount of energy, the ranges of the Nd:YAG laser spot increased with the grayscale value of the targets (P < 0.05). The greater the transmittance of the filters employed, the larger the range of the Nd: YAG laser spots produced. Assuming that the total pulse energy is identical, the effect ranges of multi-pulse burst modes were significantly larger than those of single-pulse burst mode (P < 0.05). The effect range of a Nd:YAG laser grows with increasing energy and the target's grayscale value. A cloudy refractive medium has a negative impact on the effect range of the Nd: YAG laser. The single pulse mode has the narrowest and safest efficiency range.

Electrocoagulation in treatment of municipal wastewater- life cycle impact assessment.

The purpose of this study is investigation of electrocoagulation (EC) as a treatment of municipal wastewater, integrating life cycle impact assessment (LCIA) for assessing its environmental performance of investigated treatment. The study evaluated the effectiveness of EC in removing physico-chemical and microbial parameters using aluminum (Al) and iron (Fe) electrodes in monopolar and bipolar modes. Bipolar arrangement of Al(-)/Al/Al/Al(+) electrodes achieved the highest removals: 70% COD, 72% BOD5 followed by complete elimination of total phosphorous, turbidity and microbial parameters. This treatment was subject to investigation of the influence of reaction time (t = 10-60 min) on removals at higher current density (CD = 3.33 mA/cm2). In order to reduce energy consumption, the same reaction time range was used with a reduced CD = 2.33 mA/cm2. Following removal efficiencies obtained: 47-72% COD (higher CD) and 53-78% (lower CD); 69-75% BOD5 (higher CD) and 55-74% CD (lower CD); 12-21% NH4- (higher CD) and 7-22% NH4- (lower CD). Total P, NO3- and NO2- compounds showed the same removals regardless the CD. Decrease in current density did not influence removals of total suspended matter, turbidity, salinity as well as microbial parameters. The bipolar arrangement of Al(-)/Al/Al/Al(+) electrodes, assuming a lower CD = 2.33 mA/cm2 and t = 30 min, was assessed with the Recipe 2016Midpoint (H) and USEtox v.2 LCIA methods to explore the environmental justification of using EC for wastewater treatment. The LCIA results revealed that the EC process significantly reduces water eutrophication and toxicity for freshwater and marine ecosystems, but has higher impacts in global warming, fossil fuel consumption, human toxicity, acidification, and terrestrial ecotoxicity due to high energy consumption. This can be mainly explained by the assumption in the study that the EC precipitate is dispersed to agricultural soil without any pre-treatment and material recovery, along with relatively high energy consumption during the process.

A low-cost process for complete utilization of bauxite residue.

Cost-effective treatment or even valorization of the bauxite residue (red mud) from the alumina industry is in demand to improve their environmental and economic liabilities. This study proposes a strategy that provides a near-complete conversion of bauxite residue to valuable products. The first step involves dilute acid leaching, which allowed the fractionation of raw residues into (1) an aqueous fraction rich in silica and aluminium and (2) a solid residue rich in iron, titanium and rare earth elements. For the proposed process, 91% of the original silicon, 67% of the aluminium, 78% of the scandium and 69% of the cerium were recovered. The initial cost evaluation suggested that this approach is profitable with a gross margin of 167 $US per tonne. This "Residue2Product" approach should be considered for large-scale practices as one of the most economical and sustainable solutions to this environmental and economic liability for the alumina industry.

Cone-beam computed tomography (CBCT) dose optimization technique and image quality assessment scoring.

INTRODUCTION: Linear accelerator (LINAC) embedded with kV source-imager system is capable to do image-guided radiotherapy. The only disadvantage of cone-beam computed tomography image acquisition during treatment is the extra radiation dose to the patient. The aim of this study is to optimize the CBCT imaging doses likely to be received by the patient undergoing radiotherapy without affecting image quality. MATERIAL AND METHODS: The imaging dose to the patient was estimated on CTDI phantoms. The effect of additional filters of different materials (copper, brass, aluminum of thickness 0.1 mm each) was evaluated to find the optimized dose imaging technique. For the pelvis, a single imaging protocol available on the machine was used, whereas for the head and neck region, two protocols, high-quality head and standard-dose head were used. The image quality was assessed on CATPHAN-504 phantom using Owl CATPHAN® QA online tool. A new term "Image Assessment score" (IAS) was introduced to evaluate the image quality. RESULT: In the pelvis protocol, CBCT imaging doses with an additional 0.1-mm brass, copper, and aluminum filter were measured to be reduced by 7.1%, 4.7%, and 2.5%, respectively, whereas for high-quality head protocol, the dose reduction was 25.4% (with brass filter), 22% (with copper filter), and 3.1% (with aluminum filter). For the standard-dose head protocol, doses were reduced by 7.5%, 2.8%, and 2.1% with additional 0.1-mm brass copper and aluminum filters, respectively. Acceptable image quality was observed with all the filters. CONCLUSION: Although the reconstructed images were found somewhat noisier, they did not affect the purpose of imaging, that is, treatment position verification. It was observed that these extra filters further reduce the imaging dose without much affecting the image quality.

Low-Cost Arduino Reverse Transcriptase Loop-Mediated Isothermal Amplification (RT-LAMP) for Sensitive Nucleic Acid Detection.

This work presents a low-cost transcription loop-mediated isothermal amplification (RT-LAMP) instrument for nucleic acid detection, employing an Arduino Nano microcontroller. The cooling system includes customized printed circuit boards (PCBs) that serve as electrical resistors and incorporate fans. An aluminum block is designed to accommodate eight vials. The system also includes two PCB heaters-one for sample heating and the other for vial lid heating to prevent condensation. The color detection system comprises a TCS3200 color 8-sensor array coupled to one side of the aluminum heater body and a white 8-LED array coupled to the other side, controlled by two Multiplexer/Demultiplexer devices. LED light passes through the sample, reaching the color sensor and conveying color information crucial for detection. The top board is maintained at 110 ± 2 °C, while the bottom board is held at 65 ± 0.5 °C throughout the RT-LAMP assay. Validation tests successfully demonstrated the efficacy of the colorimetric RT-LAMP reactions using SARS-CoV-2 RNA amplification as a sample viability test, achieving 100% sensitivity and 97.3% specificity with 66 clinical samples. Our instrument offers a cost-effective (USD 100) solution with automated result interpretation and superior sensitivity compared to visual inspection. While the prototype was tested with SARS-CoV-2 RNA samples, its versatility extends to detecting other pathogens using alternative primers, showcasing its potential for broader applications in biosensing.

Impact of grazing around industrial areas on milk heavy metals contamination and reproductive ovarian hormones of she-camel with assessment of some technological processes on reduction of toxic residue concentrations.

Heavy metals are one of the most toxic chemical pollutants of the environment. Their hazards not restricted to human but extend to animal productivity and reproductively. The present study aimed to assess the impact of grazing around industrial areas on the levels of copper (Cu) and aluminum (Al) residues in milk samples collected from dromedary she-camels and studying their effects on some ovarian hormones. In addition, the study aimed to investigate methods of removal of the toxic concentrations of these heavy metals in milk by applying different technological processes. Blood and milk samples were collected from 30 dromedary she-camels, 15 grazing in non-industrial areas (group A) and 15 grazing in industrial areas (group B). Detection of the levels of these heavy metals in milk was done. Ovarian hormones investigation on the blood was performed. Different technological processes such as boiling, skimming and fermentation were applied to all contaminated samples to reduce the toxic concentrations of these heavy metals. Results revealed that all examined milk samples in both groups contained Cu, while 40% of group A and 100 % of group B contained Al residues with different concentrations. The levels of Cu and Al residues in samples of group A not exceeded the maximum residual limit (MRL) set by World Health Organization (WHO) while 60% and 100% of milk samples in group B contained Cu and Al residues exceeded MRL, respectively. Technological processes induce variant changes in the levels of these metals in milk. Heat treatment of milk in Al vats leads to leaching of Al from containers to the milk causing significant increase in Al load, while Cu level was not significantly affected. Boiling in stainless-steel containers decreased the levels of Al and Cu but in non-significant levels. Regarding skimming process, small amount of Cu and Al escaped into the skimmed milk while greater amount were recovered in the cream. Fermentation by probiotic bacteria showed that milk fermentation has non-significant effect on Cu and Al levels. Investigation of ovarian hormones (estrogen and progesterone) revealed presence of a signification reduction in the levels of these hormones in group B compared to group A. In addition, a negative correlation was found between these heavy metals and ovarian hormones concentrations in the blood. It is concluded that grazing of dromedary camels around industrial areas induce heavy metals toxicity represented by excretion of these metals in milk and significant reduction on ovarian function showed by reduction of estrogen and progesterone levels. Technological processes such as skimming decreased the levels of Al and Cu residues in milk.

Technical note: A preliminary assessment of UV-C imaging using the Full Spectrum Imaging System (FSIS-II) for the detection of latent fingermarks.

The Full Spectrum Imaging System (FSIS-II) was assessed for the detection of latent fingermarks on a variety of substrates, specifically focusing on UV-C imaging for untreated marks and those that have been treated with cyanoacrylate (CA). The use of UV-C was effective at the detection of latent fingermarks on a variety of substrates and UV-C imaging may be effective when UV-A does not provide any fingermark detections on thermal paper. A Phase 2 and a small Phase 3 trials on aluminium cans were carried out with a detection sequence of UV-C imaging, CA fuming, UV-C imaging, UV-A imaging and BY40. For Phase 2 laboratory trials, the use of initial UV-C reflection was effective at removing the background and was a useful tool for initial screening. The use of UV-C was superior to UV-A after CA fuming and provided the highest overall number of high-quality marks. For phase 3 trials, the results showed that BY40 fluorescence was marginally more effective than UV-C imaging of CA-treated marks. This preliminary study shows that the FSIS-II and UV-C imaging can complement other methods for the detection of latent fingermarks.

Assessment of temperature and time on the survivability of porcine reproductive and respiratory syndrome virus (PRRSV) and porcine epidemic diarrhea virus (PEDV) on experimentally contaminated surfaces.

Fomites might be responsible for virus introduction in swine farms, highlighting the importance of implementing practices to minimize the probability of virus introduction. The study's objective was to assess the efficacy of different combinations of temperatures and holding-times on detecting live PRRSV and PEDV on surfaces commonly found in supply entry rooms in swine farms. Two PRRSV isolates (MN 184 and 1-4-4 L1C variant) and one PEDV isolate (NC 49469/2013) were inoculated on cardboard and aluminum. An experimental study tested combinations of four temperatures (20°C, 30°C, 40°C, and 50°C) and six holding-times (15 minutes, 60 minutes, 6 hours, 12 hours, 24 hours, and 36 hours) for the presence of the viruses on each surface type. After virus titration, virus presence was assessed by assessing the cytopathic effects and immunofluorescence staining. The titers were expressed as log10 TCID50/ml, and regression models; half-lives equations were calculated to assess differences between treatments and time to not detect the live virus. The results suggest that the minimum time that surfaces should be held to not detect the virus at 30°C was 24 hours, 40°C required 12 hours, and 50°C required 6 hours; aluminum surfaces took longer to reach the desired temperature compared to cardboard. The results suggest that PRRSV 1-4-4 L1C variant had higher half-lives at higher temperatures than PRRSV MN 184. In conclusion, time and temperature combinations effectively decrease the concentration of PRRSV and PEDV on different surfaces found in supply entry rooms in swine farms.

Exposure to endocrine disrupting chemicals from beverage packaging materials and risk assessment for consumers.

This study investigated the influence of beverage packaging materials on the presence of endocrine disrupting chemicals (EDCs) in plastic, glass, carton, aluminium, and tin canned non-alcoholic beverages. Results showed that 63 EDCs including perfluoroalkyl and polyfluoroalkyl substances (PFAS), bisphenols, parabens, benzophenone-type UV-filters, biocides, nitrophenols, and alkylphenols, were detected in 144/162 screened products. Detected ∑63EDC concentrations ranged from 1.3 to 19,600 ng/L. EDC concentrations were higher in beverages packaged in metal cans while lower or no levels were detected in glass, plastic, and carton packaged drinks. Bisphenol levels were higher on average in canned beverages compared to glass (p < 0.01) and plastic products (p < 0.05) produced by the same brand and manufacturer. Two structural isomers of bisphenol A (BPA) were identified in 19 beverages, constituting the first detection in foodstuffs. The calculated daily intake of detected EDCs showed that exposure to BPA from per capita beverage consumption of 364 mL/day are up to 2000-fold higher than the newly revised safety guideline for BPA recommended by the EFSA (European Food Safety Authority). Overall, these findings suggest that BPA exposure poses a potential health hazard for individuals who regularly consume non-alcoholic beverages packaged in aluminium or tin cans, particularly young children.

Experimental validation of energy dependences of YALO3:Mn TL detectors: irradiation to ISO radiation qualities.

The effect of application of filters, made of different materials and various thickness, is studied by Monte Carlo calculations using MCNP6.2 code. The calculated data were validated by experimental studies (benchmark tests). Experimental results obtained for YAlO3:Mn high-Z TL detectors irradiated to different standard ISO radiation qualities (X-ray series N-40, N-60, N-80, N-100, N-120, N-150 and N-200 as well as isotopic series S-Cs) modified by various metal (copper and aluminum) filters of thickness of 0.5, 0.8 and 1 mm. The experimental results are compared with results of Monte Carlo simulations done for the same 'radiation-attenuator-detector' combinations and geometry. Obtained results show good consistence between the experimental and calculated data that testifies adequacy of the used calculations and their applicability to modeling of modification of an output from the high-Z detectors exposed to photons of various energies.

An assessment of the pH changes and metal ions released into artificial saliva by fake orthodontic braces.

BACKGROUND: This present study assesses changes in the pH as well as the metal ions that fake braces release into artificial saliva (AS) using a pH meter and inductively coupled plasma atomic emission spectroscopy (ICP-AES), respectively. METHODS: Three sets of fake archwires (AWs) and brackets (Bs) as well as a set of controls were immersed in AS and placed in an incubator shaker at 50 rpm and 37°C. At Days 0, 1, 7, 14, 21, and 28, the pH of the AS medium was measured and 3.0 ml of AS was collected and stored at -20°C for elemental analysis. RESULTS: Significant changes in pH were observed on Days 0, 1, 7, 14, 21, and 28 in the AS of the AW group. However, these changes were only observed in the B group on Days 0 and 7. The fake samples released a large quantity of sodium (Na), potassium (K), and calcium (Ca) ions, at concentrations exceeding 100 mg/L, post-28 days of immersion. The control and fake braces samples released other ions; such as lithium (Li), magnesium (Mg), barium (Ba), chromium (Cr), copper (Cu), lead (Pb), and aluminium (Al); at concentrations that did not exceed 10 mg/L. CONCLUSIONS: The pH of the AS of all the samples increased post-incubation. Only 10 ions; namely, Na, Li, K, Mg, Ca, Ba, Cr, Cu, Pb, and Al; were detected in the AS.

Monte Carlo model of a prototype flat-panel detector for multi-energy applications in radiotherapy.

BACKGROUND: The incorporation of multi-energy capabilities into radiotherapy flat-panel detectors offers advantages including enhanced soft tissue visualization by reduction of signal from overlapping anatomy such as bone in 2D image projections; creation of virtual monoenergetic images for 3D contrast enhancement, metal artefact reduction and direct acquisition of relative electron density. A novel dual-layer on-board imager offering dual energy processing capabilities is being designed. As opposed to other dual-energy implementation techniques which require separate acquisition with two different x-ray spectra, the dual-layer detector design enables simultaneous acquisition of high and low energy images with a single exposure. A computational framework is required to optimize the design parameters and evaluate detector performance for specific clinical applications. PURPOSE: In this study, we report on the development of a Monte Carlo (MC) model of the imager including model validation. METHODS: The stack-up of the dual-layer imager (DLI) was implemented in GEANT4 Application for Tomographic Emission (GATE). The DLI model has an active area of 43×43 cm2 , with top and bottom Cesium Iodide (CsI) scintillators of 600 and 800 µm thickness, respectively. Measurement of spatial resolution and imaging of dedicated multi-material dual-energy (DE) phantoms were used to validate the model. The modulation transfer function (MTF) of the detector was calculated for a 120 kVp x-ray spectrum using a 0.5 mm thick tantalum edge rotated by 2.5o . For imaging validation, the DE phantom was imaged using a 140 kVp x-ray spectrum. For both validation simulations, corresponding measurements were done using an initial prototype of the imager. Agreement between simulations and measurement was assessed using normalized root mean square error (NRMSE) and 1D profile difference for the MTF and phantom images respectively. Further comparison between measurement and simulation was made using virtual monoenergetic images (VMIs) generated from basis material images derived using precomputed look-up tables. RESULTS: The MTF of the bottom layer of the dual-layer model shows values decreasing more quickly with spatial frequency, compared to the top layer, due to the thicker bottom scintillator thickness and scatter from the top layer. A comparison with measurement shows NRMSE of 0.013 and 0.015 as well as identical MTF50 of 0.8 mm1 and 1.0 mm1 for the top and bottom layer respectively. For the DE imaging of the DE-phantom, although a maximum deviation of 3.3% is observed for the 10 mm aluminum and Teflon inserts at the top layer, the agreement for all other inserts is less than 2.2% of the measured value at both layers. Material decomposition of simulated scatter-free DE images gives an average accuracy in PMMA and aluminum composition of 4.9% and 10.3% for 11-30 mm PMMA and 1-10 mm aluminum objects respectively. A comparison of decomposed values using scatter containing measured and simulated DE images shows good agreement within statistical uncertainty. CONCLUSION: Validation using both MTF and phantom imaging shows good agreement between simulation and measurements. With the present configuration of the digital prototype, the model can generate material decomposed images and virtual monoenergetic images.

An integrated biological effects assessment of the discharge water into the Sunndalsfjord from an aluminium smelter.

An integrated biological effects study using field transplanted mussels was applied to determine the potential biological effects of an effluent discharge from an aluminium smelter into a Norwegian fjord. Chemical body burden and biological effects were measured in mussels positioned downstream (1, 2, 5, 10 and 20 km) from the aluminium smelters discharge for a period of 6 weeks. A suite of biomarkers, from whole organism to subcellular responses were measured. Chemical concentrations in mussel tissues were low; however, a change in the PAC (polyaromatic compound) profile from high to low pyrogenic influence provided evidence of exposure to the smelter's effluent. Overall, the biological responses observed where greater in the mussels positioned closest to the smelter (1-5 km). Lowest chemical accumulation and biomarker responses were observed in mussels positioned 10 km from the smelter and were considered as the reference field population. Mussels located furthest from the smelter (20 km) exhibited significant biomarker responses and suggested a different contaminant source within the fjord. The integrated biological response index (IBR) was applied and reflected the expected level of exposure to the smelters discharge, with highest IBR calculated in mussels positioned closest to the discharge (1-5 km). Principal component analysis (PCA) also differentiated among mussel groups, with the most impacted located closest to the smelter. Not one chemical factor could explain the biological responses observed in mussels, but the presence of PAH16, PAH41 and metals Mn, Ni and Cr were the main contributors measured to the higher stress seen in the mussels from the 1 and 5 km groups.

A new fractional Cattaneo model for enhancing the thermal performance of photovoltaic panels using heat spreader: energy, exergy, economic and enviroeconomic (4E) analysis.

A new fractional non-Fourier (Cattaneo) photovoltaic (PV) model is presented to enhance the thermal performance of a PV system combined with a heat spreader (HS). The fractional Cattaneo model is shown to be effective in examining transient processes across the entirety of a PV system, in contrast to the conventional Fourier model's inability to predict system performance. Consequently, a comparison is conducted between the classical Fourier model with the fractional Fourier and fractional Cattaneo models for the PV system. The impact of using an aluminum heat spreader, with rectangular and trapezoidal shapes, has been developed under hot and cold climate conditions. The findings show that adding a trapezoidal heat spreader reduced the cell temperature by 20 K in summer and 12 K in winter. The reduction in the PV temperature led to an enhancement in daily average power by approximately 28% and 37% in hot and cold weather, respectively. Moreover, economic, exergoeconomic, and enviroeconomic assessment is introduced. The outcomes revealed that the electrical production costs of the rectangular and trapezoidal HS systems are 0.272 and 0.214 $/kWh, respectively, while about 0.286 $/kWh for the conventional PV panel. Based on the environmental study, the estimated CO2 reduction for PV, PV with rectangular HS, and PV with trapezoidal spreader is 0.5504, 0.7704, and 0.8012 tons, respectively. Finally, real experimental data are used to validate the fractional Cattaneo model. The results demonstrate that there is a great fitting with the measured data, with errors in PV power and exergy efficiency of just 0.628% and 3.84%, respectively, whereas their corresponding values for the classical model are 5.72 and 13.13%.

Oily wastewater treatment by a continuous flow electrocoagulation reactor with polarity switch: Assessment of the relation between process variables and the aluminum released to the environment.

Electrocoagulation with electrical polarity inversion was used to treat oil in water emulsions (145 ± 5 mg dm-3) using a cylindrical 4.8 dm3 reactor in continuous mode. The effects of spatial time and time between polarity inversion were explored using a three-level full factorial design (32), followed by Spearman correlation (ps), which has shown that the aluminum concentration in the treated effluent is not directly dependent on the mass of aluminum released by the electrodes. Nonetheless, the loss of mass of the electrodes is correlated (ps = 0.6970) to oil removal and to less electric power consumption (ps = -0.6909). Surface response analysis revealed that increasing the number of inversion cycles reduces electrode degradation. The treatment reduced the effluent's chemical oxygen demand by over 92.8%. Regarding environmental impact, there is an inverse statistical correlation between aluminum in the treated effluent and oil removal (ps = -0.7426), indicating that removing more oil with less environmental impact is possible. The better condition, considering oil removal and lower electrode consumption, was obtained with a spatial time of 36 min and a polarity inversion time of 10 s; for this condition, oil removal reached 87.0% with an energy expenditure of about 7.21 kW h.m-3.

Energy, exergy, exergo-economic, enviro-economic, exergo-environmental, exergo-enviro-economic, sustainability and sensitivity (6E,2S) analysis on single slope solar still-An experimental study.

Tackling water scarcity is a significant challenge due to the rapid increase in the global population, which is raising concern for the supply of fresh water. high demand of fresh water leading to a failure in meeting the demand for fresh water. This study aims to investigate the feasibility of an efficient single-slope solar still with an aluminum-finned plate absorber and internal and external reflectors to address water scarcity. Energy, exergy, economic and environmental analyses (6E) were undertaken to deeply analyze its impact on the environment. The maximum energy and exergy efficiency achieved was 60.19% and 21.57%, respectively, at a 2cm depth. The use of both external and internal reflectors assisted in the highest productivity of 7.02 liters. The cost of 0.033$/liter was obtained for a lifetime of 10 years for the optimal system. The payback time in terms of energy and exergy for the optimal system is 0.88 and 2.23 years, respectively. Furthermore, sustainability and sensitivity (2S) analysis were also performed to assess the system's current and future feasibility. The total price for carbon dioxide mitigation during the solar still lifetime was $346.7, which represents the cost saving achieved with the installation of the optimal system.

Erbium:Yttrium Aluminum Garnet (Er:YAG) Laser: A Minimally Invasive Treatment Method in Selected Patients with Impaired Breathing During Sleep-The Assessment of Treatment Effectiveness After 4 Years.

Objective: The aim of this study was to assess the long-term outcomes of nonablative Er:YAG laser treatment for snoring. Background data: Nonablative Er:YAG laser treatment has been shown to improve subjective quality of sleep without serious adverse effects, but long-term data are lacking. Materials and methods: Twenty-four patients with snoring problems due to soft palate hypertrophy were treated with three treatment procedures with Er:YAG laser performed at 2-week intervals. Subjective (questionnaires) and objective (polygraph) outcome measures were assessed at baseline, 3 months, and 4 years after the final laser treatment. Results: Twenty patients returned for the 4 years follow-up. The significant improvement in subjective sleep outcomes observed 3 months after Er:YAG laser treatment was still significant 4 years after treatment. No significant improvement or deterioration in objective polygraph outcome measures was observed during the 4 years of follow-up in our study. No side effects of laser treatment were observed. Conclusions: The Er:YAG laser treatment presents a safe and well-tolerated snoring treatment alternative for patients with airway obstruction in the oropharynx with improvement in subjective sleep outcomes lasting up to 4 years.

Proposing an intelligent technique based on radial basis function neural network to forecast the energy spectrum of diagnostic X-ray imaging systems.

In digital subtraction angiography (digital subtraction total cerebral angiography), cardiac and macrovascular cardiography, anorectal radiology, fluoroscopy, and computed tomography (CT), a prior knowledge to X-ray energy spectrum is crucial for assessing the image quality and also calculating patient X-ray dosage. The present investigation's main objective is to propose an intelligent technique for faster calculating X-ray energy spectrum of medical imaging systems with different exposure settings of tube voltage, filter material, and thickness based on limited specific spectra. In this study, Monte Carlo N Particle (MCNP) simulation code was initially used to generate some limited X-ray spectra for tube voltages of 20, 30, 40, 50, 80, 100, 130, and 150 kV for two different filters of beryllium and aluminum with thicknesses of 0. 4, 0.8, 1.2, 1.6 and 2 mm. Tube voltage, type, and thickness of filter were used as the 3 inputs of 150 Radial Basis Function Neural Network (RBFNN) to forecast point by point of the X-ray spectrum. After training, the RBFNNs could forecast most of the X-ray spectra for tube voltages in the range of 20-150 kV and two various filters of aluminum and beryllium with thicknesses in the range of 0-2 mm.

A novel combined metallurgy-beneficiation method for the facile and low-cost comprehensive resource utilization of low-grade kaolin solid wastes.

Low-grade kaolin is the largest emissions of industrial solid waste that is difficult to dispose of and pollutes the environment seriously. From the perspective of harmless and complete resource utilization, we proposed a novel strategy that combines the wet leaching under mild conditions and physical beneficiation for the facile and low-cost high-valued utilization of low-grade kaolin that involves high-efficiency recovery of aluminum (Al), silicon (Si), and titanium (Ti). The key to successful implementation of this method lies in the new discovery that the residual SiO2 after Al extraction of kaolinite by acid leaching under specific conditions could be rapidly dissolved in dilute NaOH solution at room temperature 25 °C. This highly reactive SiO2 challenges the conventional notions of various silica species are usually chemically stable. By adjusting the key technical parameters of the thermal activation-acid leaching process, the selective and efficient extraction of Al2O3 from low-grade kaolin was realized. The acid leaching residue was then subjected to selective recovery of SiO2 by alkaline leaching at 25 °C to obtain high-quality sodium silicate. Finally, the alkali leaching residue as titanium coarse concentrate was separated by centrifugal concentrator to obtain artificial rutile (TiO2 >91.06%). The key mechanism for the formation of the highly reactive silica was also systematically studied and confirmed.